Consumer Electronics

View as Grid List

Sort by

Display per page

Waveshare 13.3 inch Mini-Computer Powered by Raspberry Pi 3A+, HD Touch Screen (EU Plug)

13.3 inch IPS screen,1920 x 1080 high resolution.
Embed Raspberry Pi 3A+ as controller.
Toughened glass capacitive touch panel, 6H hardness, supports up to 10-points touch.
Embedded ferrite Hi-Fi speaker.
Embedded microphone and speaker, adopts snowboy hotword detection engine.
75x75mm spacing mounting holes (M4 screw hole).
Comes with a 75 degree tilt angle stand.
Package List

C$399.19 C$463.06

I2C bus, allows expanding 16 I/O ports by just using two wires
Support driving 16-ch common anode constant current LED, 256-step linear dimming, current controllable
Output interrupt (INT) signal when changing the state of an input port
I2C address configurable by shorting the A0/A1 jumpers
Provide two connector options: PH2.0 header and/or solder pads, allows multi I2C modules to be stacked
Onboard voltage translator, compatible with 3.3V/5V level
Come with development resources and manual (examples for Raspberry Pi / micro:bit / Arduino / STM32)
Working voltage: 2.4-5.5V

C$15.00 C$18.45

Standard 40PIN GPIO extension header, supports direct attaching to Jetson Nano
Onboard CAN controller MCP2515 via SPI interface, matching with SIT65HVD230DR transceiver
Features RS485 function, controlled via UART, half-duplex communication, supports automatic TX/RX control without programming, onboard transceiver SP3485
Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit for RS485 transceiving, light-ningproof & anti-electrostatic
Onboard digital isolation chip, safer signal isolation communication and better stability and anti-interference
Reserved control pins, allows to work with other control boards
Comes with development resources and manual (examples in python)
CAN Controller: MCP2515

C$37.70 C$43.36

Onboard switch chip, 5x ports 10/100/1000M non-blocking switch architecture
Full-duplex 10/100/1000M support for each port (the half-duplex 100M connection is only supported on 10/100M mode)
Full/Half-duplex operations with IEEE 802.3x flow control and back pressure support
Allow forwarding 9216 bytes huge data packet on linear speed
Over-voltage protection, effectively preventing damages caused by other high voltage power supply
Industrial grade alloy case, solid and durable, with DIN rail mount support for easy installing
5~36V wide voltage power supply, dual power interface (DC interface and terminal block) onboard overvoltage protection, reverse connection protection.
Support 25mm standard rail.

C$40.97 C$48.33

3.5 inch IPS screen, hardware resolution is 640 ?? 480.
5-point capacitive touch, tempered glass panel, hardness up to 6H.
When used with Raspberry Pi, supports Raspberry Pi OS / Ubuntu / Kali and Retropie.
When used with Tinker Board 2, it supports Android / Debian.
Ubuntu is supported when used with Jetson Nano.
When used as a computer monitor, supports Windows 11/10/8.1/8/7.
Onboard dual touch circuit, optional USB Type-C or I2C touch, more application scenarios.
With 3.5mm audio and speaker interface, support HDMI audio output.

C$71.38 C$85.67

C$24.72 C$29.91

C$18.64 C$21.99

Onboard standard CM4 connector, support access to CM4 Lite / eMMc series boards with Quad Core Cortex A72 64-bit processor, more powerful performance
Easily compatible with the interfaces of Raspberry Pi 3B / 3B+ boards
Onboard headphone jack (extended from USB)
Onboard 4-ch USB ports, compatible with USB 2.0 / 1.1 transmission
Onboard RJ45 Gigabit Ethernet port, 10 / 100 / 1000 M adaptive
Onboard PoE header, for connecting PoE HATs

C$41.55 C$47.78